A2N Kernel Control S8/S8+/N8

## Supports all S8/S8+/Note8 Exynos Variants ##

Note: works only with A2N Kernel + Root.

## App Features ##

# CPU/GPU
-- Overclock Control
-- Voltage Control
-- Stable CPU OC up to 2,0 GHz/2,8 GHz (lit/big)
-- Stable GPU OC up to 839 MHz
Ability to use different CPU Freqs while the screen is OFF.
Ability to disable boost, for better battery life.
Governor up_threshold, to adjust balance between performance and powersave.
DVFS Max Temp (thermal throttling) - Range: 55 - 100 °C - Default 65 °C.
To avoid too big performance drops from stock thermal throttling driver.
-- Input Booster
Adjust touch boost CPU duration in ms, to improve scrolling.
Ability to use only the little CPU.

# Performance Profiles
-- Powersave
-- Balanced (Power Efficient)
-- Performance (Kernel Default, customizable in CPU/GPU menu)
-- Performance Plus (Gaming / OC) (customizable CPU/GPU Freq below the profile)

# Power
-- Charger Control
Adjustable Max input current in 100 mA steps. - Range: 200 - 3000/3300/3500 mA (S8/Note8/S8+) - Default: 1500 mA.
This affects the time required for charging the battery.
For the S8: the original AC charger (9.0 V -- 1.67 A // 5.0 V -- 2.0 A) is enough to achieve 3000 mA charging current.
For the S8+ make sure that your USB charger supports min. 9.0 V -- 2.0 A or 5.0 V -- 3.5 A.

-- Battery Informations
Charging current, input voltage (5 or 9 V), temperature and voltage.

-- Battery Care
E.g. stop charging at 95 % to reduce battery aging. - Range: 50 - 100 % - Default 100 %.
Battery IDLE feature, useful for DeX or gaming.
Limit charging temperature. - Range: 30 - 45 °C - Default 40 °C.
This will throttle charger input current if needed.

-- Battery Service
Shows charge cycles and ability to reset it.
Check real battery capacity in % / mAh and ability to reset it. (battery gauge recalibration)

-- Disable (Buggy) Moisture Detection
Ability to disable this, for the case that the USB- or Jack port is dry but you get still a warning.

# Screen
HDMI/DEX custom resolution changer (to fix low resolution / refresh rate)

# RAM
-- Memory Management
Swap / zRam* - LZ4 compressed swap block-device in RAM - Choice: 0 - 100 % of RAM size.
Adjust Swappiness, page-cluster and read_ahead_kb.
Ability to drop caches / buffers, to free RAM.

* For multitasking, gaming, responsiveness and battery life.

# Network
Load kernel module for network file systems
SMB2/SMB3 / CIFS
NFS v2, v3 & v4
L2TP - used for VPN.
Wireguard - Secure Network Tunnel.
TCP Congestion Control - Choice: cubic, new reno, bic, westwood+ etc ...
Wi-Fi Band Selection, choice: "2.4 GHz / 5 GHz", "2.4 GHz only" or "5 GHz only".

# Misc
-- Torchlight Tuning
Increase brightness. - Range: 1 - 17 (to get brighter torch)
-- LED-RGB
Set blink ON / OFF delay for notifications / low battery.
Increases brightness of the LED by disabling powersave mode.
-- Accelerometer Calibration
# File Systems
-- Load kernel module - NTFS.

# Advanced Power Menu
Ability to reboot to recovery / download-mode
## END App Features ##

## FAQ ##
Q: Is this app 100 % safe ?
A: Yes.

Q: Will this app overheat the phone if I use highest settings ?
A: No, you can't do anything wrong. Your phone has hard- and software overheat protection.

Q: Will this app change anything if I just flash A2N Kernel and install and start this app ?
A: No, the app will set on startup several kernel settings, but those are same as kernel default. To improve speed or battery life you need to change settings in this app.

Q: Will this app restore my settings at next boot ?
A: Yes, after the app passes license check.

Q: How to revert all changes made by this app ?
A: Uninstall this app and reboot the phone.

## Requirements ##
Search for "A2N Kernel S8 XDA", there is everything you need.
Note: this app need internet for license check.

## CREDITS ##
-- World-gear-symbol by Freepik from www.flaticon.com - edited by ace2nutzer